fertinnovative.blogg.se - Peterbilt king pins

PETERBILT KING PINS INSTALL
PETERBILT KING PINS PLUS

PETERBILT KING PINS PLUS

Of course all the seals, and shims, (sometimes) are included. 2000 Mack RD688 King Pin Set 1,500 USD ROUND TUBE DROP CENTER (855) 905- SHOW NUMBER Email Seller More Info 1 0 Meritor MFS-16 King Pin Set 342.77 USD (NEW) Meritor MFS-16 Axle Model: MFS-20 TRUEFIT PLUS NO-REAM KIT (855) 370- SHOW NUMBER Email Seller More Info 1 0 Eaton E-1000I King Pin Set 226. The top should be a needle bearing pack, the bottom a pre sized bushing that does not require reaming to size. That is not too difficult of job but if needing to go that far just get a king pin, (or bolt) kit and replace everything. If you can't get that clearance close the thrust bearing is probably worn out and time for replacement. 005 between the spindle and top of the axle beam with the axle loaded. You would be adjusting for a clearance of about. Hi Mark, the link does not appear to function properly. It is a good idea to keep the adj in specsĪs to not have too mutch float as to pound the thrust button to bits.Mark

PETERBILT KING PINS INSTALL

Thrust bearings should be pre-packed before you install them to ensure proper lubrication.Fjh is right the only adjustment to stop the knuckle binding on the beam.Īs a straight pin at either end when the bushings/ bearings are worn there is The weight on the axle rests on these bearings.

Thrust bearings – Thrust bearings are roller bearings that sit at the bottom of the axle against the steering knuckle.

As the bolt is tightened the wedge squares the king pin against the axle.

Keeper – Keepers are bolts that have a wedge-shaped head and retain the king pins in the axle.

Truck manufacturers will have specifications for each model on how much travel is allowable and shims will be added or removed to meet this specification. Shims will be used on the top of the axle between the spindle and the axle.

Shims – Shims are used to control play between the steering knuckle and the axle.

Incorrectly installing the seals may block grease from reaching the bushings. It is important to install the seal in the correct direction to allow the grease to flow through the bushings.

Seals – Seals install at the top and bottom of the king pin to retain the grease.

The caps install in the top and bottom of the spindle and seal in grease while providing threads to install a grease zirc.

Caps – King pin caps will be included when needed.

The type of kit that you have purchased will dictate whether you have spiral bushings or standard bi-metal bushings. Keep away from Meritor stuff it is differentt to the old stuff. There will be four bushings, two for each spindle. Rod,Go to Mack and ask for King Pin set 501SQ45A.

Steering Knuckle bushings – Bushings will be included that are installed in the steering knuckle.

King pins are machined to fine tolerances to fit the axle precisely. These may be a single or double keeper (using one or two keeper bolts) The diameter and length of the pin are critical to finding the correct replacement kit.

King pins – Large Hardened steel pins.

Most king pin kits will include the following items: Heavy duty steel trailer king pin lock is designed to prevent theft of the trailer by preventing a tractors fifth wheel from attaching onto the king pin. King pin kits are specific for each axle model and the kits will include all necessary components to refurbish the axle and steering knuckle. If you are self-installing, it will require the assistance of a machine shop to fit the pins to the steering knuckle. Standard king pin kits are typically used by shops since special tools are required to line bore the bushings in the steering knuckle. The bushings included in a standard king pin kit will need to be reamed to fit the new pin after they are installed in the steering knuckle. Bronze is used on the inside portion of the bushing due to its anti-friction and wear-resistant properties, bronze will only become damaged if lubrication is not present. Steel is used for the outer portion of the bushing to allow it to be pressed into the steering knuckle without deforming the inner bronze area. Standard king pin kits use solid bi-metal bronze and steel bushings. You can avoid a machine shop using a spiral bushing kit so if you are servicing your own truck this is the kit to use. Spiral kits are the ideal kit to use if you do not have the capability to press new bushing into the steering knuckles and ream them to fit the pins. These bushings can be installed by twisting into the spindle using an installation tool and they do not require reaming. Spiral bushing kits use a coiled, spiral-shaped bushing. There are two main options for king pin kits to accomplish the job of replacement. Performing a king pin rebush job is a major undertaking so it is best to be prepared for the task with a replacement king pin kit.